Brittany Beckmann 13 Comments

Powder coating can be a delicate matter. It requires precision, a keen eye and thoroughly maintained processes to ensure that nothing mars the finish. HUI powder coats its industrial products in-house and follows a strict set of guidelines to combat and avoid common powder coating mistakes.

Regular Treatments

Following through with weekly preventative maintenance practices, especially specific cleaning methods, go a long way as far as avoiding mistakes and painting flaws. From a daily standpoint, an appointed person physically writes the powder colors on deck for that day in a place where everyone can see it so paint technicians can cross-reference that with the interactive scheduling program.

Best Powder Coating Application Practices

Excellent powder coating methods require exact setup, communication and controlled, competent workmanship. The application process starts before anything gets painted.

1. Gun Set-Up

Painters always check their paint guns before painting. Laminated set-up sheets are kept on the paint booths at all times to assist anyone in need of help. Painters check for worn parts and change them immediately to make sure nothing hinders how powder flows from the gun. If a gun tip happens to fall on the floor, it gets blown off with an air hose and wiped clean with water before reuse.

2. Communication

As with most jobs, communication is essential for avoiding most powder coating mistakes. When painting with a partner, it’s crucial for both parties to discuss methods and strategies they can use together to produce an error-free finish. At HUI, we cross-train all paintline technicians, which allows for more flexibility and makes maintaining a steady work pace much easier.

3. Plan of Attack

During this step, the painter will ask him or herself a series of questions before starting. The list of questions include:

  • Is my gun set-up correctly?
  • Do I know what I’m painting and what my partner is painting?
  • Which section of this part is the most difficult to paint?
  • Are there any seams, corners, bends, recesses and so on?

4. Gun Speed

Gun speed can be a difficult concept to understand, especially for new painters. Paint too fast, and the powder won’t stick. Paint too slow, and you’ll fall behind. It’s something that needs to be felt. The general rule, which will vary, dictates that a painter shouldn’t move his or her gun much more than 24 to 30 inches within the time it takes to say “one-one thousand.” After you get the hang of it, painting should be a relaxed practice.

5. Gun Distance

Similar to speed, gun distance can be difficult to grasp at first. General distance rule dictates that the gun should maintain a distance of six to eight inches from a flat surface and three to eight inches away from a seam or recess. The latter depends on how difficult it is to reach the recessed area and is up to the painter’s discretion.

However, if the painter does need to paint at a closer distance, this means that the gun speed must also increase to avoid painting too heavily in that area.

If the gun is too close to the surface, it may result in a variety of flaws: paint streaks, runs or sags, peeling or uneven film thickness.

Additional Tips

Unless there’s a special coating or finishing requirement, you’ll get much more consistent results when everyone uses the same type of gun tip.

A designated person dedicates his or her entire work day to the powder room to ensure the highest paint quality and is responsible for enforcing regular treatments and best power coat applications. The powder person also manages the color changes and looks over painted parts for quality.

At HUI, we uphold high standards for our powder coat processes to ensure the finish on your custom enclosure and other industrial product meets your expectations.

If you have any questions regarding our powder paint coating and finishing processes or you’re looking to manufacture a custom enclosure or industrial product, please contact us today!

Powder Coating Glosses and Finishes Options eBook

— 13 Comments —

  1. This is some really good information about powder coating. It does seem like a good thing to be aware of if you want to make your things last for a long time. I know that I wouldn’t want to have to keep putting new coats on all the time.

  2. I appreciate this article about how to avoid common powder coating mistakes. It is good to know that gun set-up is crucial. I did not realize that experienced painters always check their guns before painting. Something to consider would be to seek professional help with a project like this to ensure quality work and safety.

  3. I have been thinking about getting the new rims on my car powder coated. I had no idea that different gun tips could cause different finishes with the coating. I’ll be sure when my rims are coated that the painter uses the same tip on all four rims as well.

  4. I restore motorcycles as a hobby. Most of the time, I’ll have parts that need to be coated by a heat-resistant coating. I learned that powder coating is the best option for me since it’s durable. It’s great that you mentioned how powder coating requires precision and a thoroughly maintained process to achieve a good finish. I was planning on doing it on my own but I guess. I’d rather have a professional apply the coating for me to make sure I get good results.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.